高温高压下Zr2AlC的结构及热学性质的第一性原理

利用密度泛函理论研究了高温高压下Zr₂AlC的结构和热力学性质,计算得到Zr₂AlC的晶格参数与实验值符合较好．研究了Zr₂AlC的弹性常数、体模量、剪切模量和杨氏模量等力学性质随压力变化的趋势．同时研究了维氏硬度随压力的变化趋势．通过计算得到的杨氏模量预测了Zr₂AlC的弹性各向异性．最后,基于准简谐德拜模型,成功预测了Zr₂AlC的德拜温度、热容、热膨胀系数和Grüneisen参数随着压强和温度的变化关系.     

飞秒激光冲击AZ31B镁合金过程的数值模拟

采用有限元分析法对飞秒激光冲击AZ31B镁合金进行数值模拟,研究了激光冲击处理对镁合金变形过程的影响,分析了单脉冲激光冲击下材料内部的位移、动能、应力和应变的分布情况,得到了材料的瞬态速度和应变率变化过程.仿真结果表明,单脉冲飞秒激光冲击镁合金产生的塑性变形,可在材料表面形成微米级凹坑,中心点处最大位移为34μm,最大变形速度390m/s;在冲击初期,材料表面的应力和应变主要分布在冲击区域中心节点和边缘附近,并且得到镁合金的最大应力和最大应变率分别为955 MPa和1.8×106 s-1.研究结果能够为深入分析飞秒激光与镁合金作用时材料变形参量的变化规律提供数值理论依据.     

铜铟铝硒硫薄膜的低成本非真空混合法制备

采用溶剂热法制备出铜铟铝硒Cu(In,Al)Se₂ (CIASe)粉末,然后滴涂铜铟铝硒CIASe浆料获得前驱体薄膜,最后通过硒化/硫化过程制备出铜铟铝硒CIASe和铜铟铝硒硫CIASeS薄膜．通过XRD、SEM、XRF及光吸收等表征,发现所制备的薄膜为单相的黄铜矿结构,具有(112)择优取向．同时,在使用硫元素替代硒之后,薄膜的XRD主峰向高的2θ角度漂移,多孔薄膜也变得更加致密．薄膜带隙值也增加到更为合适的范围,从1.21 eV增加到1.33 eV,这也说明了硫化过程有利于提高CIASeS薄膜的质量．     

Decoupled two‐grid finite element method for the time‐dependent natural convection problem I: Spatial discretization

In this article, a decoupled two grid finite element method (FEM) is proposed and analyzed for the nonsteady natural convection problem using the coarse grid numerical solutions to decouple the nonlinear coupled terms, and the corresponding optimal error estimates are derived. Compared with the standard Galerkin FEM and the usual two‐grid FEM, our algorithm not only keeps good accuracy but also saves a lot of computational cost. Some numerical examples are provided to verify the performances of the decoupled two‐grid FEM. Both theoretical analysis and numerical experiments show the efficiency and effectiveness of the decoupled two‐grid FEM for the nonsteady natural convection problem. © 2015 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq 31: 2135–2168, 2015     

Improvement of resistive switching fluctuations by using one step lift‐off process

Bipolar resistive switching characteristics are investigated in ZrO₂ containing Cu thin layer devices, particularly for the self‐isolated‐structure device fabricated by one step lift‐off process. Compared with the traditional‐structure device, the self‐isolated‐structure device shows more uniform resistive switching characteristics. This is because the isolation of each device cell has negligible influence on each other and thus mitigates possible crosstalk between each cell. These results suggest that the feasibility of good stabilization of the resistive switching parameters can be obtained through one step lift‐off process. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Spin gapless semiconductor like Ti2MnAl film as a new candidate for spintronics application

A novel Heusler ferrimagnet Ti₂MnAl film has been grown on Si(001) substrate using magnetron sputtering. Characteristics of its magnetic and transport properties reveal the spin‐gapless‐semiconductor (SGS) nature of the stoichiometric Ti₂MnAl, in agreement with theoretical prediction. The as‐grown SGS‐like Ti₂MnAl film demonstrated high Curie temperature, nearly compensated ferrimagnetic properties with small coercivity and low magnetization. It also showed semiconductor‐like behavior at room temperature allowing good compatibility with commercial Si‐based semiconductor. In this regards, Ti₂MnAl film is a potential candidate material for spintronics application, especially for the minimization of energy consumption of device. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

导弹发射姿态测量方法研究

针对导弹发射姿态测量问题,提出采用高速摄像机通过斜瞄和平瞄姿态测量方法求解导弹中轴线俯仰角和方位角,仿真典型导弹起飞段近距离姿态测量,分析两种测量方法对导弹飞行姿态测量精度和适用性。仿真结果表明:平瞄和斜瞄姿态测量方法,测量误差在0.2°以内。斜瞄方式使用更便捷,通用性好。平瞄方式测量精度高,数据处理方法、机械结构相对简单,在适合的应用场合优势明显。此分析方法、分析结果为姿态测量方法选取和研究等提供一种可行的途径,也可为其它运动目标的姿态测量提供借鉴。     

Distributed Bragg reflector laser(1.8 μm) with 10 nm wavelength tuning range

We report a 1.8 μm two-section distributed Bragg reflector laser using butt-jointed In Ga As P bulk material as the waveguide core layer. The threshold current is 17 m A and the output power is 8 m W on average. The threshold current, output power, and emitting wavelength dependences on temperature are measured. The obtained wavelength tuning range is 10 nm. This device has potential applications in simultaneous multiple-gas detection.     

Electrochemical performance of lithium ion capacitors with different types of negative electrodes

The electrochemical properties of various commercial carbon materials (activated carbon (AC), graphite (GP) and hard carbon (HC)) have been investigated for use as negative electrode for lithium ion capacitors. The rate capabilities and cycle durabilities are tested up to 20 C and 1000 cycles using full cell configurations. It is found that the lithium ion could not efficiently intercalate into the activated carbon materials. The symmetrical AC/AC capacitor shows good cycle durabilities at 10 C with capacity of 17 mA h g^?1. The asymmetrical capacitors AC/GP and AC/HC with intercalated negative electrodes show higher capacities than that of AC/AC capacitor. Moreover, the AC/HC has better rate capabilities than AC/GP.     

Ordered Mesoporous Carbon and Thiolated Polyaniline Modified Electrode for Simultaneous Determination of Cadmium(II) and Lead(II) by Anodic Stripping Voltammetry

The fabrication and evaluation of a glassy carbon electrode (GCE) modified with ordered mesoporous carbon (OMC), 2‐mercaptoethanesulfonate (MES)‐tethered polyaniline (PANI) and bismuth for simultaneous determination of trace Cd²⁺ and Pb²⁺ by differential pulse anodic stripping voltammetry (DPASV) are presented here. The morphology and electrochemical properties of the fabricated electrode were respectively characterized by scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). Experimental parameters such as PANI disposition, preconcentration potential, preconcentration time and bismuth concentration were optimized. Under optimum conditions, the fabricated electrode exhibited linear calibration curves ranged from 1 to 120 nM for Cd²⁺ and Pb²⁺. The limits of detection (LOD) were 0.26 nM for Cd²⁺ and 0.16 nM for Pb²⁺ (S/N=3), respectively. Additionally, repeatability, reproducibility, interference and application were also investigated, and the proposed electrode exhibited excellent performance. The proposed method could be extended for the development of other new sensors for heavy metal determination.